false

Whether edge scrolling is enabled

When enabled, touchpads that support edge scrolling will have that feature enabled. true

Whether edge scrolling is enabled

When enabled, touchpads that support two-finger scrolling will have that feature enabled. false

Enable mouse clicks with touchpad

Set this to TRUE to be able to send mouse clicks by tapping on the touchpad. 'enabled'

Touchpad enabled

Defines the situations in which the touchpad is enabled. 'mouse'

Touchpad button orientation

Swap left and right mouse buttons for left-handed mice with 'left', 'right' for right-handed, 'mouse' to follow the mouse setting. 0

Pointer speed

Pointer speed for the touchpad. Accepted values are in the [-1..1] range (from "unaccelerated" to "fast"). A value of 0 is the system default. true

Natural scrolling

Set this to TRUE to enable natural (reverse) scrolling for touchpads. 'default'

Click method

How to generate software-emulated buttons, either disabled ('none'), through specific areas ('areas'), number of fingers ('fingers') or left as hardware default ('default'). true

Keyboard repeat

Set this to TRUE to enable keyboard repeat. 30

Key Repeat Interval

Delay between repeats in milliseconds. 500

Initial Key Repeat Delay

Initial key repeat delay in milliseconds. false

Mouse button orientation

Swap left and right mouse buttons for left-handed mice. 0

Pointer speed

Pointer speed for mice. Accepted values are in the [-1..1] range (from "unaccelerated" to "fast"). A value of 0 is the system default. false

Natural scrolling

Set this to TRUE to enable natural (reverse) scrolling for mice. 'default'

Acceleration profile

Acceleration profile used for connected mice. The acceleration profile can be set to either default ('default') which uses the default acceleration profile for each device, flat ('flat'), which accelerates by a device specific constant factor derived from the configured pointer speed, or adaptive ('adaptive') which adapts the acceleration depending on the mouse movement. If a mouse doesn't support the configured profile, 'default' will be used. ["", "", ""]

Drawing tablet mapping

EDID information of the monitor the tablet is mapped to. Must be in the format [vendor, product, serial]. ["","",""] disables mapping. 'absolute'

Tablet mapping

How input affects the pointer on the screen [0, 0, 0, 0]

Tablet area

Dead area padding around the active area, in percentages. Respectively applied to left,right,top and bottom sides. false

Tablet aspect ratio

Enable this to restrict the tablet area to match the aspect ratio of the output. false

Tablet left-handed mode

Enable this to allow physically rotating the tablet for left-handed setups [0, 0, 100, 100]

Stylus pressure curve

Set this to x1, y1 and x2, y2 of the pressure curve applied to the stylus. [0, 0, 100, 100]

Eraser pressure curve

Set this to x1, y1 and x2, y2 of the pressure curve applied to the eraser. 'default'

Button action

Stylus button action, this button is located along the pen handle. 'default'

Secondary button action

Secondary stylus button action, this button is located along the pen handle on some styli like the Grip Pen. Other styli like the Airbrush Pen or the Inking Pen only have one button, this setting is ineffective on those. 'none'

Pad button action type

The type of action triggered by the button being pressed. ''

Key combination for the custom action

The keyboard shortcut generated when the button is pressed for custom actions. ["", "", ""]

Touchscreen display mapping

EDID information of the monitor the touchscreen is mapped to. Must be in the format [vendor, product, serial]. ["","",""] disables mapping. 0

Mouse wheel emulation button. 0 to disable the feature.

'default'

Acceleration profile

Acceleration profile used for the trackball. The acceleration profile can be set to either default ('default') which uses the default acceleration profile, flat ('flat'), which accelerates by a device specific constant factor derived from the configured speed, or adaptive ('adaptive') which adapts the acceleration depending on the movement. If the trackball doesn't support the configured profile, 'default' will be used.